|
|
|
|
|
Red Head TruBolt 12377 Wedge Anchor, 1/4 in Dia, 2-1/4 in OAL
|
|
TruBolt wedge anchors offer maximum strength and ultimate flexibility making them the PRO choice for heavy-duty anchoring. This wedge anchor features a high-strength body that is built to resist tension and shear loads and it is code approved for use in uncracked concrete. For additional application versatility, TruBolt wedge anchors are fully threaded to accommodate a greater range of fixture thicknesses. The wedge anchor's stainless steel clip provides extended corrosion resistance to ensure the long-term integrity of connections.
|
|
|
|
|
|
|
|
Simpson Strong-Tie Strong-Bolt 2 STB2-50334C10 Wedge Anchor, 1/2 in Dia, 3-3/4 in L, Carbon Steel, Zinc Plated
|
|
Code listed for cracked and uncracked concrete and masonry applications, the Strong-Bolt 2 wedge-type expansion anchor is an optimal choice for high-performance even in seismic and high-wind conditions. Dual undercutting embossments on each clip segment enable secondary expansion should a crack form and intersect the anchor location; this feature significantly increases the ability of Strong-Bolt 2 to carry load if the hole expands.
|
|
|
|
|
|
|
|
Simpson Strong-Tie Strong-Bolt 2 STB2-37334C15 Wedge Anchor, 3/8 in Dia, 3-3/4 in L, Carbon Steel, Zinc Plated
|
|
Code listed for cracked and uncracked concrete and masonry applications, the Strong-Bolt 2 wedge-type expansion anchor is an optimal choice for high-performance even in seismic and high-wind conditions. Dual undercutting embossments on each clip segment enable secondary expansion should a crack form and intersect the anchor location; this feature significantly increases the ability of Strong-Bolt 2 to carry load if the hole expands.
|
|
|
|
|
|
|
|
DeWALT Zamac Nailin 2808 Nail Anchor, 1/4 in Dia, 1 in L, Carbon Steel/Zamac, 100/BX
|
|
The Zamac Nailin? is a nail drive anchor which has a body formed from Zamac alloy. The anchor can be used in concrete, block, brick or stone. A corrosion-resistant Zamac alloy is used to form the anchor body with either a mushroom or flat head. The anchor can be used for light-duty, tamper-proof applications.
|
|
|
|
|
|
|
|
DeWALT Zamac Nailin 2814 Nail Anchor, 1/4 in Dia, 1-1/4 in L, Carbon Steel/Zamac
|
|
The Zamac Nailin? is a nail drive anchor which has a body formed from Zamac alloy. The anchor can be used in concrete, block, brick or stone. A corrosion-resistant Zamac alloy is used to form the anchor body with either a mushroom or flat head. The anchor can be used for light-duty, tamper-proof applications.
|
|
|
|
|
|
|
|
Simpson Strong-Tie Strong-Bolt 2 STB2-50512C10 Wedge Anchor, 1/2 in Dia, 5-1/2 in L, Carbon Steel, Zinc Plated
|
|
Code listed for cracked and uncracked concrete and masonry applications, the Strong-Bolt 2 wedge-type expansion anchor is an optimal choice for high-performance even in seismic and high-wind conditions. Dual undercutting embossments on each clip segment enable secondary expansion should a crack form and intersect the anchor location; this feature significantly increases the ability of Strong-Bolt 2 to carry load if the hole expands.
|
|
|
|
|
|
|
|
Red Head 12019 Wedge Anchor, 1/2 in Dia, 5-1/2 in OAL, Carbon Steel, Zinc
|
|
Trubolt? Wedge anchors feature a stainless steel expansion clip, threaded stud body, nut and washer. Anchor bodies are made of plated carbon steel, hot-dipped galvanized carbon steel, type 304 stainless steel or type 316 stainless steel as identified in the drawings or other notations. The exposed end of the anchor is stamped to identify anchor length. Stampings should be preserved during installation for any subsequent embedment verification. Use carbide tipped hammer drill bits made in accordance with ANSI B212.15-1994 to install anchors. Anchors are tested to ACI 355.2 and ICC-ES AC193.
|
|
|
|
|
|
|
|
ANCHOR DROP-IN SGL 1/2 - Case of 10
|
|
For fastening applications in solid concrete. Contractor-grade anchors. Internally threaded. For overhead applications, transformers and meters, ceiling fans, electrical light fixtures.
|
|
|
|
|
|
|
|
Red Head Hammer-Set 35303 Anchor, 1/4 in Dia, 1-1/2 in L, Steel, Zinc
|
|
For fastening applications in concrete, block and brick. For brackets, drywall track, gutters and down spouts, electrical boxes.
|
|
|
|
|
|
|
|
Red Head Hammer-Set 35305 Anchor, 1/4 in Dia, 2 in L, Steel, Zinc
|
|
For fastening applications in concrete, block and brick. For brackets, drywall track, gutters and down spouts, electrical boxes.
|
|
|